I'm trying to help someone out and save them some money by doing the work myself instead of sending them to a mechanic. Any advice would be very helpful. Thanks.How tricky is it to do a brake job on a 2000 Ford F250 4x4?I probably shouldn't be telling you how to do this job, but here it goes. Jack up and support the front of the vehicle, making sure the rear wheels are blocked safely. Remove all eight 21mm wheel nuts on both front wheels. Remove the wheels. Turn front wheels fully to the left. Remove the two 17 or 18mm caliper bolts. Remove the caliper, taking care not to let the caliper hang by the flex hose. You make need to unclip the wheel speed sensor harness from the flex hose clips. With a long johnson bar and 1/2%26quot; drive 21mm socket, loosen and remove the two 21mm brake caliper bracket bolts. Remove the caliper bracket with the brake pads. Using one of the old brake pads and a pair of channel lock pliers, compress BOTH caliper pistons evenly, until both pistons are bottomed out. With a suitably sized hammer, smash the brake rotor off the hub. Clean the hub surface with sandpaper, and apply a light coat of anti-seize to the hub. Install new brake rotor, and secure rotor to hub temporarily with two wheel nuts. Reinstall the caliper bracket with the new pads and anti-rattle clips. Reinstall the brake caliper. Turn wheel all the way to the right, and repeat entire procedure described. Once all is done, PUMP THE BRAKE PEDAL BEFORE YOU ATTEMPT TO MOVE IT. Torque wheel nuts to 140 ft.-lbs. You do not need to disturb anything with the 4x4 system, or ABS for this job. Nor are any special tools required. Hope this helps.
Thursday, June 2, 2011
How tricky is it to do a brake job on a 2000 Ford F250 4x4?
I want to know about changing just front pads and rotors on this truck. I've only worked on older cars (1979 and earlier), and I've never done a brake job on anything that had ABS or that was 4 wheel drive. Are there any special tools or procedures I need to be aware of?
I'm trying to help someone out and save them some money by doing the work myself instead of sending them to a mechanic. Any advice would be very helpful. Thanks.How tricky is it to do a brake job on a 2000 Ford F250 4x4?I probably shouldn't be telling you how to do this job, but here it goes. Jack up and support the front of the vehicle, making sure the rear wheels are blocked safely. Remove all eight 21mm wheel nuts on both front wheels. Remove the wheels. Turn front wheels fully to the left. Remove the two 17 or 18mm caliper bolts. Remove the caliper, taking care not to let the caliper hang by the flex hose. You make need to unclip the wheel speed sensor harness from the flex hose clips. With a long johnson bar and 1/2%26quot; drive 21mm socket, loosen and remove the two 21mm brake caliper bracket bolts. Remove the caliper bracket with the brake pads. Using one of the old brake pads and a pair of channel lock pliers, compress BOTH caliper pistons evenly, until both pistons are bottomed out. With a suitably sized hammer, smash the brake rotor off the hub. Clean the hub surface with sandpaper, and apply a light coat of anti-seize to the hub. Install new brake rotor, and secure rotor to hub temporarily with two wheel nuts. Reinstall the caliper bracket with the new pads and anti-rattle clips. Reinstall the brake caliper. Turn wheel all the way to the right, and repeat entire procedure described. Once all is done, PUMP THE BRAKE PEDAL BEFORE YOU ATTEMPT TO MOVE IT. Torque wheel nuts to 140 ft.-lbs. You do not need to disturb anything with the 4x4 system, or ABS for this job. Nor are any special tools required. Hope this helps.reliable web hosting child beauty pageants
I'm trying to help someone out and save them some money by doing the work myself instead of sending them to a mechanic. Any advice would be very helpful. Thanks.How tricky is it to do a brake job on a 2000 Ford F250 4x4?I probably shouldn't be telling you how to do this job, but here it goes. Jack up and support the front of the vehicle, making sure the rear wheels are blocked safely. Remove all eight 21mm wheel nuts on both front wheels. Remove the wheels. Turn front wheels fully to the left. Remove the two 17 or 18mm caliper bolts. Remove the caliper, taking care not to let the caliper hang by the flex hose. You make need to unclip the wheel speed sensor harness from the flex hose clips. With a long johnson bar and 1/2%26quot; drive 21mm socket, loosen and remove the two 21mm brake caliper bracket bolts. Remove the caliper bracket with the brake pads. Using one of the old brake pads and a pair of channel lock pliers, compress BOTH caliper pistons evenly, until both pistons are bottomed out. With a suitably sized hammer, smash the brake rotor off the hub. Clean the hub surface with sandpaper, and apply a light coat of anti-seize to the hub. Install new brake rotor, and secure rotor to hub temporarily with two wheel nuts. Reinstall the caliper bracket with the new pads and anti-rattle clips. Reinstall the brake caliper. Turn wheel all the way to the right, and repeat entire procedure described. Once all is done, PUMP THE BRAKE PEDAL BEFORE YOU ATTEMPT TO MOVE IT. Torque wheel nuts to 140 ft.-lbs. You do not need to disturb anything with the 4x4 system, or ABS for this job. Nor are any special tools required. Hope this helps.
